Ich meine das XW oder XM stand in der dmesg vom Bootloader wenn man seriell dran hängt. Mal dmesg via SSH probiert?
Ich selber habe keines der Geräte zur Hand / kein SSH Zugriff.
Hatte gehofft, dass jemand die Info im Kopf hat.
Hi!
Hier dmesg per SSH einer UbiQuiti NanoStation Loco M2, geflashed mit Bullet-M.
Gruss,
Micha
[ 0.000000] Linux version 3.18.29 (admin@pudding) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r49097) ) #1 Thu Apr 28 12:28:32 CEST 2016
[ 0.000000] MyLoader: sysp=b2aaaaaa, boardp=2a3aaaab, parts=aaaaaaaa
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR7241 rev 1
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x01ffffff]
[ 0.000000] On node 0 totalpages: 8192
[ 0.000000] free_area_init_node: node 0, pgdat 803742b0, node_mem_map 81000000
[ 0.000000] Normal zone: 64 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 8192 pages, LIFO batch:0
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: board=UBNT-BM console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,7552k(firmware),256k(cfg)ro,64k(EEPROM)ro rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 28324K/32768K available (2573K kernel code, 133K rwdata, 540K rodata, 264K init, 193K bss, 4444K reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Clocks: CPU:390.000MHz, DDR:390.000MHz, AHB:195.000MHz, Ref:5.000MHz
[ 0.000000] Calibrating delay loop... 259.27 BogoMIPS (lpj=1296384)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.080000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090000] NET: Registered protocol family 16
[ 0.090000] MIPS: machine is Ubiquiti Bullet M
[ 0.100000] registering PCI controller with io_map_base unset
[ 0.330000] PCI host bridge to bus 0000:00
[ 0.330000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[ 0.340000] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.340000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.350000] pci 0000:00:00.0: [168c:002e] type 00 class 0x028000
[ 0.350000] pci 0000:00:00.0: fixup device configuration
[ 0.350000] pci 0000:00:00.0: reg 0x10: [mem 0x10000000-0x1000ffff 64bit]
[ 0.350000] pci 0000:00:00.0: supports D1
[ 0.350000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.350000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.350000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit]
[ 0.360000] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.360000] Switched to clocksource MIPS
[ 0.370000] NET: Registered protocol family 2
[ 0.370000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.370000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.380000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.390000] TCP: reno registered
[ 0.390000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.400000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.400000] NET: Registered protocol family 1
[ 0.410000] PCI: CLS 0 bytes, default 32
[ 0.410000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.430000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.430000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.440000] msgmni has been set to 55
[ 0.450000] io scheduler noop registered
[ 0.450000] io scheduler deadline registered (default)
[ 0.460000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.470000] console [ttyS0] disabled
[ 0.490000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 12187500) is a 16550A
[ 0.500000] console [ttyS0] enabled
[ 0.510000] bootconsole [early0] disabled
[ 0.520000] m25p80 spi0.0: found mx25l6405d, expected m25p80
[ 0.520000] m25p80 spi0.0: mx25l6405d (8192 Kbytes)
[ 0.530000] 5 cmdlinepart partitions found on MTD device spi0.0
[ 0.530000] Creating 5 MTD partitions on "spi0.0":
[ 0.540000] 0x000000000000-0x000000040000 : "u-boot"
[ 0.540000] 0x000000040000-0x000000050000 : "u-boot-env"
[ 0.550000] 0x000000050000-0x0000007b0000 : "firmware"
[ 0.570000] 2 uimage-fw partitions found on MTD device firmware
[ 0.580000] 0x000000050000-0x00000016ebcb : "kernel"
[ 0.580000] 0x00000016ebcb-0x0000007b0000 : "rootfs"
[ 0.590000] mtd: device 4 (rootfs) set to be root filesystem
[ 0.600000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.600000] 0x0000003b0000-0x0000007b0000 : "rootfs_data"
[ 0.610000] 0x0000007b0000-0x0000007f0000 : "cfg"
[ 0.610000] 0x0000007f0000-0x000000800000 : "EEPROM"
[ 0.650000] libphy: ag71xx_mdio: probed
[ 1.250000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[ 1.260000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 1.260000] TCP: cubic registered
[ 1.270000] NET: Registered protocol family 17
[ 1.270000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.290000] Bridge firewalling registered
[ 1.290000] 8021q: 802.1Q VLAN Support v1.8
[ 1.300000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 1.310000] Freeing unused kernel memory: 264K (8038e000 - 803d0000)
[ 2.760000] init: Console is alive
[ 2.760000] init: - watchdog -
[ 4.880000] init: - preinit -
[ 5.630000] random: procd urandom read with 8 bits of entropy available
[ 9.070000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x10000
[ 9.080000] jffs2_build_filesystem(): unlocking the mtd device... done.
[ 9.090000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
[ 35.120000] jffs2: notice: (327) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 35.140000] mount_root: overlay filesystem has not been fully initialized yet
[ 35.150000] mount_root: switching to jffs2 overlay
[ 36.190000] procd: - early -
[ 36.200000] procd: - watchdog -
[ 37.020000] procd: - ubus -
[ 38.030000] procd: - init -
[ 39.410000] NET: Registered protocol family 10
[ 39.420000] tun: Universal TUN/TAP device driver, 1.6
[ 39.430000] tun: (C) 1999-2004 Max Krasnyansky
[ 39.440000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 39.470000] batman_adv: B.A.T.M.A.N. advanced 2015.1 (compatibility version 15) loaded
[ 39.490000] u32 classifier
[ 39.490000] input device check on
[ 39.490000] Actions configured
[ 39.500000] Mirror/redirect action on
[ 39.550000] Loading modules backported from Linux version v4.4-rc5-1913-gc8fdf68
[ 39.560000] Backport generated by backports.git backports-20151218-0-g2f58d9d
[ 39.610000] Ebtables v2.0 registered
[ 39.620000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 39.640000] nf_conntrack version 0.5.0 (446 buckets, 1784 max)
[ 39.770000] xt_time: kernel timezone is -0000
[ 40.010000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 40.020000] ath: phy0: Ignoring endianness difference in EEPROM magic bytes.
[ 40.030000] ath: EEPROM regdomain: 0x0
[ 40.030000] ath: EEPROM indicates default country code should be used
[ 40.030000] ath: doing EEPROM country->regdmn map search
[ 40.030000] ath: country maps to regdmn code: 0x3a
[ 40.030000] ath: Country alpha2 being used: US
[ 40.030000] ath: Regpair used: 0x3a
[ 40.050000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 40.050000] ieee80211 phy0: Atheros AR9287 Rev:2 mem=0xb0000000, irq=40
[ 60.080000] random: nonblocking pool is initialized
[ 61.560000] device eth0 entered promiscuous mode
[ 61.600000] IPv6: ADDRCONF(NETDEV_UP): br-wan: link is not ready
[ 61.710000] IPv6: ADDRCONF(NETDEV_UP): br-client: link is not ready
[ 61.720000] device br-client entered promiscuous mode
[ 61.730000] IPv6: ADDRCONF(NETDEV_UP): local-node: link is not ready
[ 65.980000] IPv6: ADDRCONF(NETDEV_UP): client0: link is not ready
[ 66.030000] device client0 entered promiscuous mode
[ 66.060000] br-client: port 1(client0) entered forwarding state
[ 66.070000] br-client: port 1(client0) entered forwarding state
[ 66.070000] IPv6: ADDRCONF(NETDEV_CHANGE): client0: link becomes ready
[ 66.110000] IPv6: ADDRCONF(NETDEV_CHANGE): br-client: link becomes ready
[ 66.110000] IPv6: ADDRCONF(NETDEV_CHANGE): local-node: link becomes ready
[ 66.880000] IPv6: ADDRCONF(NETDEV_UP): ibss0: link is not ready
[ 66.950000] ibss0: Created IBSS using preconfigured BSSID 02:04:08:16:32:64
[ 66.960000] ibss0: Creating new IBSS network, BSSID 02:04:08:16:32:64
[ 67.110000] IPv6: ADDRCONF(NETDEV_CHANGE): ibss0: link becomes ready
[ 67.380000] batman_adv: bat0: Adding interface: ibss0
[ 67.380000] batman_adv: bat0: Interface activated: ibss0
[ 67.390000] 8021q: adding VLAN 0 to HW filter on device bat0
[ 67.430000] device bat0 entered promiscuous mode
[ 67.430000] br-client: port 2(bat0) entered forwarding state
[ 67.440000] br-client: port 2(bat0) entered forwarding state
[ 68.070000] br-client: port 1(client0) entered forwarding state
[ 68.240000] batman_adv: bat0: Changing gw mode from: off to: client
[ 68.310000] batman_adv: bat0: gw_sel_class: Changing from: 20 to: 15
[ 68.310000] batman_adv: bat0: hop_penalty: Changing from: 30 to: 15
[ 68.340000] batman_adv: bat0: multicast_mode: Changing from: enabled to: disabled
[ 68.370000] batman_adv: bat0: orig_interval: Changing from: 1000 to: 5000
[ 69.440000] br-client: port 2(bat0) entered forwarding state
Mhh, schade. Ich hab nochmal nachgeschaut, über die Konsole meldete nur der U-Boot die Version (schade), noch bevor der ganze dmesg Kram kommt:
Wenn ich das richtig verstanden habe, dann ist die „normale“ Nanostation loco die „XM“, also die images, die z.b. so aussehen:
gluon-ffXX-2016.1.6-ubiquiti-loco-m-sysupgrade.bin
Und seit 2016.2 hat sich der name nochmal leicht geaendert, da sehen die dann so aus:
gluon-ffXX-2016.2.1~exp1612011339-ubiquiti-nanostation-loco-m2-sysupgrade.bin
(mit nanostation- mittendrin)
richtig?
ja, richtig.
ob man die -xw- images braucht, sieht man meines Wissens erst, wenn man sich in der stock firmware weboberfläche eingeloggt hat, das steht nicht auf Verpackung oder Gerät…
Was macht man denn nun, wenn man auf einer großen Nanostation M2 schon ewig gluon drauf hat und nun, nach Jahren, rausfinden will, welche version man jetzt fürs neu flashen nehmen muss? „XW“ oder XM"?
ohne Gewähr:
Wenn Gluon als Image nicht XW nennt, ist es implizit XM.
lua -e 'print(require("platform_info").get_image_name())'