Auf Supported Devices & Architectures — Gluon 2023.2.2 documentation ist die Rocket nicht unter ath79-generic aufgeführt, im gluon-2023-Zweig meiner Community finde ich auch kein offensichtlich passendes Image.
Wo muss ich da suchen? Oder braucht es noch etwas?
Vielen Dank
Shameless Ping @Aiyion.Prime und @Djfe …
Im aktuellen Gluon sind einige ath79-generic Devices von Ubiquiti (XW) aufgetaucht, aber nicht die Rocket M2/M5.
Ist das absehbar? Laufen die mit Nanostation-Images?
Vielen Dank!
Ping: @Aiyion.Prime @Djfe
ubiquiti-nanostation-loco-m-xw sollte das richtige Image für die sein. Dort ist es nun als alias aufgeführt:
Ich sehe sie dort eher nicht sondern eher dort:
Demnach - ich habe aber beim Lesen von derartigem Code große Defizite und bin daher für Korrekturen dankbar - wäre meiner Interpretation nach “ubnt_bullet-m-xw” das korrekte Image. Images für die Bullets wurden zumindest bislang nicht mehr von meiner Community gebaut Vielleicht mit Gluon 2025.x ja wieder …
Vielen Dank!
Afaik wurden die Rocket M XM entfernt, weil sie 2022 in Openwrt zu ath79-tiny geschoben worden:
Seit dem wurden sie jedoch 2023 in openwrt wieder zu ath79-generic gepackt:
Man kann den Geräten also neuen Gluon-Support hinzufügen, wenn jemand die Checkliste durchgehen würde und sich die Mühe macht.
Ich habe das schon einmal gemacht:
Muss die Checkliste noch einmal wiederholt werden? (ich traue mir aber nicht zu, die korrekte Umgebung für ein Gluon-Build aufzusetzen, zumal try-und-error bei meiner Hardware etwas lang werden könnte).
Kann ich sonst noch was sinnvolles tun?
Hi @Murxmaster ,
ich habe dir auf basis des aktuellen Gluons hier ein Image gebaut:
Wenn du damit einmal die Device-Checklist erneut durchgehen könntest, wäre das super.
Der letzte Durchlauf ist leider ja wieder 2 Jahre her und wir müssten das ja mit dem aktuellen main/release testen.
~~Das würde den Update-Pfad von älteren Versionen dann ermöglichen 
~~
Leider gab es keinen support von v2022.1.x welches das älteste supportete Upgrade von der 2025.1.x wäre - alte Geräte sollte man also händisch hoch ziehen..
VG
Florian
Danke, aber “geht nicht”[tm]
Ich habe das Image geflasht und konfiguriert:
Das Ethernet-Kabel in einen LAN-Anschluss gesteckt und gewartet. Nichts passiert, keine Anforderung am DHCP-Server mit dem konfiguriertem Hostname.
LAN-Kabel in den Laptop gesteckt und - siehe da - die Rocket ist wieder im Config-Modus, hat aber keine Einstellungen gespeichert.
Wenn Du Ideen hast: gerne. Ich habe gerade keine Idee für ein sinnvolles Debugging.
Es gab eben bei den UBNT XM Geräten ein Problem mit deren Flash:
Du kannst wohl im Config-mode dich über ssh verbinden und in dmesg gucken:
[ 0.387892] spi-nor spi0.0: mx25l6405d (8192 Kbytes)https://github.com/openwrt/openwrt/issues/14941#issuecomment-2260882445
Das Issue sollte eigentlich behoben sein und wurde hier getestet:
Wäre doof, wenn da schon wieder was kaputt ist.
Kannst du bitte mal von hier:
Das OpenWrt ausprobieren und gucken ob die Settings dabei zwischen reboots behalten werden?Dann gerne nochmal melden.
Nach dem Boot in config-moduse per ssh root@192.168.1.1 mal drauf gehen und ein dmesg und logread abspeichern und hier irgendwie posten wäre super zum Debuggen.
dmesg:
[ 0.000000] Linux version 6.6.119 (ffac@ffac-build) (mips-openwrt-linux-musl-gcc (OpenWrt GCC 13.3.0 r30000) 13.3.0, GNU ld (GNU Binutils) 2.42) #0 Wed Dec 3 00:00:00 2025
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[ 0.000000] MIPS: machine is Ubiquiti Rocket M (XM)
[ 0.000000] SoC: Atheros AR7241 rev 1
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, linear)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16256
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 55220K/65536K available (6199K kernel code, 581K rwdata, 1492K rodata, 1192K init, 205K bss, 10316K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 51
[ 0.000000] CPU clock: 390.000 MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9801335621 ns
[ 0.000003] sched_clock: 32 bits at 195MHz, resolution 5ns, wraps every 11012737021ns
[ 0.008048] Calibrating delay loop… 259.27 BogoMIPS (lpj=1296384)
[ 0.084161] pid_max: default: 32768 minimum: 301
[ 0.103007] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.110335] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.133567] RCU Tasks Trace: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=1.
[ 0.150407] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.160280] futex hash table entries: 256 (order: 0, 3072 bytes, linear)
[ 0.167090] pinctrl core: initialized pinctrl subsystem
[ 0.177253] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.184258] thermal_sys: Registered thermal governor ‚step_wise‘
[ 0.187654] /ahb/apb: Fixed dependency cycle(s) with /ahb/apb/interrupt-controller@18060010
[ 0.218737] clocksource: Switched to clocksource MIPS
[ 0.243401] NET: Registered PF_INET protocol family
[ 0.248680] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.258681] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.267222] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.274958] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.282621] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[ 0.289711] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.296304] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.302922] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.311136] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.316854] PCI: CLS 0 bytes, default 32
[ 0.328907] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[ 0.336228] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.342088] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.364859] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.373849] pinctrl-single 18040028.pinmux: 64 pins, size 8
[ 0.381304] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.396321] printk: console [ttyS0] disabled
[ 0.401486] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 10, base_baud = 12187500) is a 16550A
[ 0.410381] printk: console [ttyS0] enabled
[ 0.418798] printk: bootconsole [early0] disabled
[ 0.479273] spi-nor spi0.0: mx25l6405d (8192 Kbytes)
[ 0.484446] 6 fixed-partitions partitions found on MTD device spi0.0
[ 0.490948] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[ 0.497633] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[ 0.504701] Creating 6 MTD partitions on „spi0.0“:
[ 0.509580] 0x000000000000-0x000000040000 : „u-boot“
[ 0.519709] 0x000000040000-0x000000050000 : „u-boot-env“
[ 0.528235] 0x000000050000-0x0000007a0000 : „firmware“
[ 0.536896] 2 uimage-fw partitions found on MTD device firmware
[ 0.542947] Creating 2 MTD partitions on „firmware“:
[ 0.547942] 0x000000000000-0x000000280000 : „kernel“
[ 0.555826] 0x000000280000-0x000000750000 : „rootfs“
[ 0.563801] mtd: setting mtd4 (rootfs) as root device
[ 0.569121] 1 squashfs-split partitions found on MTD device rootfs
[ 0.575344] 0x000000720000-0x000000750000 : „rootfs_data“
[ 0.583802] 0x0000007a0000-0x0000007b0000 : „board_config“
[ 0.592546] 0x0000007b0000-0x0000007f0000 : „cfg“
[ 0.600378] 0x0000007f0000-0x000000800000 : „art“
[ 0.608310] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[ 0.978230] switch0: Atheros AR724X/AR933X built-in rev. 2 switch registered on mdio.0
[ 1.439386] ag71xx-legacy 19000000.eth: connected to PHY at mdio.0:1f:04 [uid=004dd041, driver=Qualcomm Atheros AR9331 built-in PHY]
[ 1.452562] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: mii
[ 1.459259] i2c_dev: i2c /dev entries driver
[ 1.469355] NET: Registered PF_INET6 protocol family
[ 1.487944] Segment Routing with IPv6
[ 1.491892] In-situ OAM (IOAM) with IPv6
[ 1.496100] NET: Registered PF_PACKET protocol family
[ 1.501262] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.514684] 8021q: 802.1Q VLAN Support v1.8
[ 1.551691] PCI host bridge to bus 0000:00
[ 1.555850] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[ 1.562912] pci_bus 0000:00: root bus resource [io 0x0000]
[ 1.568520] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 1.576574] pci 0000:00:00.0: [168c:002a] type 00 class 0x028000
[ 1.582685] pci 0000:00:00.0: reg 0x10: [mem 0x10000000-0x1000ffff 64bit]
[ 1.589709] pci 0000:00:00.0: supports D1
[ 1.593742] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 1.601198] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 1.607891] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit]
[ 1.640276] clk: Disabling unused clocks
[ 1.659371] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 1.676646] Freeing unused kernel image (initmem) memory: 1192K
[ 1.682653] This architecture does not have kernel memory protection.
[ 1.689146] Run /sbin/init as init process
[ 1.693255] with arguments:
[ 1.693264] /sbin/init
[ 1.693274] with environment:
[ 1.693283] HOME=/
[ 1.693293] TERM=linux
[ 3.065124] init: Console is alive
[ 3.069341] init: - watchdog -
[ 3.072848] init: Watchdog has previously reset the system
[ 6.282338] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 6.456930] usbcore: registered new interface driver usbfs
[ 6.462660] usbcore: registered new interface driver hub
[ 6.468236] usbcore: registered new device driver usb
[ 6.489283] gpio_button_hotplug: loading out-of-tree module taints kernel.
[ 6.527514] ehci-platform 1b000000.usb: EHCI Host Controller
[ 6.533450] ehci-platform 1b000000.usb: new USB bus registered, assigned bus number 1
[ 6.541576] ehci-platform 1b000000.usb: irq 3, io mem 0x1b000000
[ 6.568762] ehci-platform 1b000000.usb: USB 2.0 started, EHCI 1.00
[ 6.576561] hub 1-0:1.0: USB hub found
[ 6.581819] hub 1-0:1.0: 1 port detected
[ 6.604124] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 6.623376] init: - preinit -
[ 11.518787] random: crng init done
[ 16.900560] eth0: link up (100Mbps/Full duplex)
[ 19.269016] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[ 19.291059] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 19.673042] eth0: link down
[ 19.700598] procd: - early -
[ 19.703940] procd: - watchdog -
[ 19.707530] procd: Watchdog has previously reset the system
[ 20.509059] procd: - watchdog -
[ 20.512398] procd: Watchdog has previously reset the system
[ 20.546539] procd: - ubus -
[ 21.059405] procd: - init -
[ 23.627785] kmodloader: loading kernel modules from /etc/modules.d/*
[ 25.084258] GACT probability on
[ 25.100998] Mirror/redirect action on
[ 25.146250] u32 classifier
[ 25.149078] input device check on
[ 25.152754] Actions configured
[ 25.599528] Loading modules backported from Linux version v6.12.61-0-gdcbeffaf66d0
[ 25.607166] Backport generated by backports.git v6.1.110-1-35-g410656ef
[ 25.735986] xt_time: kernel timezone is -0000
[ 26.328934] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 26.336828] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld Jason@zx2c4.com. All Rights Reserved.
[ 26.425546] batman_adv: B.A.T.M.A.N. advanced 2024.3-openwrt-7 (compatibility version 15) loaded
[ 26.462034] ath9k 0000:00:00.0: Direct firmware load for ath9k-eeprom-pci-0000:00:00.0.bin failed with error -2
[ 26.472282] ath9k 0000:00:00.0: Falling back to sysfs fallback for: ath9k-eeprom-pci-0000:00:00.0.bin
[ 26.993991] ath: phy0: Ignoring endianness difference in EEPROM magic bytes.
[ 27.002691] ath: EEPROM regdomain: 0x0
[ 27.002707] ath: EEPROM indicates default country code should be used
[ 27.002718] ath: doing EEPROM country->regdmn map search
[ 27.002742] ath: country maps to regdmn code: 0x3a
[ 27.002756] ath: Country alpha2 being used: US
[ 27.002769] ath: Regpair used: 0x3a
[ 27.022290] ieee80211 phy0: Selected rate control algorithm ‚minstrel_ht‘
[ 27.024068] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0x6b16335b, irq=11
[ 27.088305] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 56.512701] ath: EEPROM regdomain: 0x8114
[ 56.512749] ath: EEPROM indicates we should expect a country code
[ 56.512762] ath: doing EEPROM country->regdmn map search
[ 56.512774] ath: country maps to regdmn code: 0x37
[ 56.512789] ath: Country alpha2 being used: DE
[ 56.512802] ath: Regpair used: 0x37
[ 56.512814] ath: regdomain 0x8114 dynamically updated by user
[ 61.599494] urngd: v1.0.2 started.
[ 77.237235] br-setup: port 1(eth0) entered blocking state
[ 77.242776] br-setup: port 1(eth0) entered disabled state
[ 77.248269] ag71xx-legacy 19000000.eth eth0: entered allmulticast mode
[ 77.255332] ag71xx-legacy 19000000.eth eth0: entered promiscuous mode
[ 79.300700] eth0: link up (100Mbps/Full duplex)
[ 79.305383] br-setup: port 1(eth0) entered blocking state
[ 79.310886] br-setup: port 1(eth0) entered forwarding state
[ 113.416517] Too few erase blocks (3)
[ 150.019105] eth0: link down
[ 150.022417] br-setup: port 1(eth0) entered disabled state
[ 155.220573] eth0: link up (100Mbps/Full duplex)
[ 155.225239] br-setup: port 1(eth0) entered blocking state
[ 155.230728] br-setup: port 1(eth0) entered forwarding state
[ 778.179108] eth0: link down
[ 778.182409] br-setup: port 1(eth0) entered disabled state
[ 869.700602] eth0: link up (100Mbps/Full duplex)
[ 869.705272] br-setup: port 1(eth0) entered blocking state
[ 869.710759] br-setup: port 1(eth0) entered forwarding state
[10264.019429] eth0: link down
[10264.022737] br-setup: port 1(eth0) entered disabled state
[10269.220898] eth0: link up (100Mbps/Full duplex)
[10269.225572] br-setup: port 1(eth0) entered blocking state
[10269.231066] br-setup: port 1(eth0) entered forwarding state
logread:
Wed Dec 3 01:00:30 2025 kern.notice kernel: [ 0.000000] Linux version 6.6.119 (ffac@ffac-build) (mips-openwrt-linux-musl-gcc (OpenWrt GCC 13.3.0 r30000) 13.3.0, GNU ld (GNU
Binutils) 2.42) #0 Wed Dec 3 00:00:00 2025
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.000000] printk: bootconsole [early0] enabled
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.000000] MIPS: machine is Ubiquiti Rocket M (XM)
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.000000] SoC: Atheros AR7241 rev 1
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.000000] Initrd not found or empty - disabling initrd
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.000000] Zone ranges:
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.000000] Movable zone start for each node
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.000000] Early memory node ranges
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
Wed Dec 3 01:00:30 2025 kern.debug kernel: [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
Wed Dec 3 01:00:30 2025 kern.debug kernel: [ 0.000000] pcpu-alloc: [0] 0
Wed Dec 3 01:00:30 2025 kern.notice kernel: [ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, linear)
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.000000] Writing ErrCtl register=00000000
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.000000] Readback ErrCtl register=00000000
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16256
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.000000] Memory: 55220K/65536K available (6199K kernel code, 581K rwdata, 1492K rodata, 1192K init, 205K bss, 10316K reserved,
0K cma-reserved)
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.000000] NR_IRQS: 51
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.000000] CPU clock: 390.000 MHz
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9801335621 ns
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.000003] sched_clock: 32 bits at 195MHz, resolution 5ns, wraps every 11012737021ns
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.008048] Calibrating delay loop… 259.27 BogoMIPS (lpj=1296384)
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.084161] pid_max: default: 32768 minimum: 301
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.103007] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.110335] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.133567] RCU Tasks Trace: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=1.
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.150407] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.160280] futex hash table entries: 256 (order: 0, 3072 bytes, linear)
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.167090] pinctrl core: initialized pinctrl subsystem
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.177253] NET: Registered PF_NETLINK/PF_ROUTE protocol family
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.184258] thermal_sys: Registered thermal governor ‚step_wise‘
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.187654] /ahb/apb: Fixed dependency cycle(s) with /ahb/apb/interrupt-controller@18060010
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.218737] clocksource: Switched to clocksource MIPS
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.243401] NET: Registered PF_INET protocol family
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.248680] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.258681] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear)
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.267222] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.274958] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.282621] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.289711] TCP: Hash tables configured (established 1024 bind 1024)
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.296304] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.302922] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.311136] NET: Registered PF_UNIX/PF_LOCAL protocol family
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.316854] PCI: CLS 0 bytes, default 32
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.328907] workingset: timestamp_bits=30 max_order=14 bucket_order=0
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.336228] squashfs: version 4.0 (2009/01/31) Phillip Lougher
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.342088] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.364859] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.373849] pinctrl-single 18040028.pinmux: 64 pins, size 8
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.381304] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.396321] printk: console [ttyS0] disabled
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.401486] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 10, base_baud = 12187500) is a 16550A
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.410381] printk: console [ttyS0] enabled
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.418798] printk: bootconsole [early0] disabled
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.479273] spi-nor spi0.0: mx25l6405d (8192 Kbytes)
Wed Dec 3 01:00:30 2025 kern.notice kernel: [ 0.484446] 6 fixed-partitions partitions found on MTD device spi0.0
Wed Dec 3 01:00:30 2025 kern.err kernel: [ 0.490948] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
Wed Dec 3 01:00:30 2025 kern.err kernel: [ 0.497633] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
Wed Dec 3 01:00:30 2025 kern.notice kernel: [ 0.504701] Creating 6 MTD partitions on „spi0.0“:
Wed Dec 3 01:00:30 2025 kern.notice kernel: [ 0.509580] 0x000000000000-0x000000040000 : „u-boot“
Wed Dec 3 01:00:30 2025 kern.notice kernel: [ 0.519709] 0x000000040000-0x000000050000 : „u-boot-env“
Wed Dec 3 01:00:30 2025 kern.notice kernel: [ 0.528235] 0x000000050000-0x0000007a0000 : „firmware“
Wed Dec 3 01:00:30 2025 kern.notice kernel: [ 0.536896] 2 uimage-fw partitions found on MTD device firmware
Wed Dec 3 01:00:30 2025 kern.notice kernel: [ 0.542947] Creating 2 MTD partitions on „firmware“:
Wed Dec 3 01:00:30 2025 kern.notice kernel: [ 0.547942] 0x000000000000-0x000000280000 : „kernel“
Wed Dec 3 01:00:30 2025 kern.notice kernel: [ 0.555826] 0x000000280000-0x000000750000 : „rootfs“
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.563801] mtd: setting mtd4 (rootfs) as root device
Wed Dec 3 01:00:30 2025 kern.notice kernel: [ 0.569121] 1 squashfs-split partitions found on MTD device rootfs
Wed Dec 3 01:00:30 2025 kern.notice kernel: [ 0.575344] 0x000000720000-0x000000750000 : „rootfs_data“
Wed Dec 3 01:00:30 2025 kern.notice kernel: [ 0.583802] 0x0000007a0000-0x0000007b0000 : „board_config“
Wed Dec 3 01:00:30 2025 kern.notice kernel: [ 0.592546] 0x0000007b0000-0x0000007f0000 : „cfg“
Wed Dec 3 01:00:30 2025 kern.notice kernel: [ 0.600378] 0x0000007f0000-0x000000800000 : „art“
Wed Dec 3 01:00:30 2025 kern.err kernel: [ 0.608310] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 0.978230] switch0: Atheros AR724X/AR933X built-in rev. 2 switch registered on mdio.0
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 1.439386] ag71xx-legacy 19000000.eth: connected to PHY at mdio.0:1f:04 [uid=004dd041, driver=Qualcomm Atheros AR9331 built-in PH
Y]
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 1.452562] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: mii
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 1.459259] i2c_dev: i2c /dev entries driver
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 1.469355] NET: Registered PF_INET6 protocol family
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 1.487944] Segment Routing with IPv6
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 1.491892] In-situ OAM (IOAM) with IPv6
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 1.496100] NET: Registered PF_PACKET protocol family
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 1.501262] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if
you need this.
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 1.514684] 8021q: 802.1Q VLAN Support v1.8
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 1.551691] PCI host bridge to bus 0000:00
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 1.555850] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 1.562912] pci_bus 0000:00: root bus resource [io 0x0000]
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 1.568520] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 1.576574] pci 0000:00:00.0: [168c:002a] type 00 class 0x028000
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 1.582685] pci 0000:00:00.0: reg 0x10: [mem 0x10000000-0x1000ffff 64bit]
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 1.589709] pci 0000:00:00.0: supports D1
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 1.593742] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 1.601198] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 1.607891] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit]
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 1.640276] clk: Disabling unused clocks
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 1.659371] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 1.676646] Freeing unused kernel image (initmem) memory: 1192K
Wed Dec 3 01:00:30 2025 kern.warn kernel: [ 1.682653] This architecture does not have kernel memory protection.
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 1.689146] Run /sbin/init as init process
Wed Dec 3 01:00:30 2025 kern.debug kernel: [ 1.693255] with arguments:
Wed Dec 3 01:00:30 2025 kern.debug kernel: [ 1.693264] /sbin/init
Wed Dec 3 01:00:30 2025 kern.debug kernel: [ 1.693274] with environment:
Wed Dec 3 01:00:30 2025 kern.debug kernel: [ 1.693283] HOME=/
Wed Dec 3 01:00:30 2025 kern.debug kernel: [ 1.693293] TERM=linux
Wed Dec 3 01:00:30 2025 user.info kernel: [ 3.065124] init: Console is alive
Wed Dec 3 01:00:30 2025 user.info kernel: [ 3.069341] init: - watchdog -
Wed Dec 3 01:00:30 2025 user.info kernel: [ 3.072848] init: Watchdog has previously reset the system
Wed Dec 3 01:00:30 2025 user.info kernel: [ 6.282338] kmodloader: loading kernel modules from /etc/modules-boot.d/*
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 6.456930] usbcore: registered new interface driver usbfs
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 6.462660] usbcore: registered new interface driver hub
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 6.468236] usbcore: registered new device driver usb
Wed Dec 3 01:00:30 2025 kern.warn kernel: [ 6.489283] gpio_button_hotplug: loading out-of-tree module taints kernel.
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 6.527514] ehci-platform 1b000000.usb: EHCI Host Controller
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 6.533450] ehci-platform 1b000000.usb: new USB bus registered, assigned bus number 1
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 6.541576] ehci-platform 1b000000.usb: irq 3, io mem 0x1b000000
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 6.568762] ehci-platform 1b000000.usb: USB 2.0 started, EHCI 1.00
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 6.576561] hub 1-0:1.0: USB hub found
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 6.581819] hub 1-0:1.0: 1 port detected
Wed Dec 3 01:00:30 2025 user.info kernel: [ 6.604124] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
Wed Dec 3 01:00:30 2025 user.info kernel: [ 6.623376] init: - preinit -
Wed Dec 3 01:00:30 2025 kern.notice kernel: [ 11.518787] random: crng init done
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 16.900560] eth0: link up (100Mbps/Full duplex)
Wed Dec 3 01:00:30 2025 user.notice kernel: [ 19.269016] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
Wed Dec 3 01:00:30 2025 user.warn kernel: [ 19.291059] urandom-seed: Seed file not found (/etc/urandom.seed)
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 19.673042] eth0: link down
Wed Dec 3 01:00:30 2025 user.info kernel: [ 19.700598] procd: - early -
Wed Dec 3 01:00:30 2025 user.info kernel: [ 19.703940] procd: - watchdog -
Wed Dec 3 01:00:30 2025 user.info kernel: [ 19.707530] procd: Watchdog has previously reset the system
Wed Dec 3 01:00:30 2025 user.info kernel: [ 20.509059] procd: - watchdog -
Wed Dec 3 01:00:30 2025 user.info kernel: [ 20.512398] procd: Watchdog has previously reset the system
Wed Dec 3 01:00:30 2025 user.info kernel: [ 20.546539] procd: - ubus -
Wed Dec 3 01:00:30 2025 user.info kernel: [ 21.059405] procd: - init -
Wed Dec 3 01:00:30 2025 user.info kernel: [ 23.627785] kmodloader: loading kernel modules from /etc/modules.d/*
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 25.084258] GACT probability on
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 25.100998] Mirror/redirect action on
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 25.146250] u32 classifier
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 25.149078] input device check on
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 25.152754] Actions configured
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 25.599528] Loading modules backported from Linux version v6.12.61-0-gdcbeffaf66d0
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 25.607166] Backport generated by backports.git v6.1.110-1-35-g410656ef
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 25.735986] xt_time: kernel timezone is -0000
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 26.328934] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 26.336828] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld Jason@zx2c4.com. All Rights Reserved.
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 26.425546] batman_adv: B.A.T.M.A.N. advanced 2024.3-openwrt-7 (compatibility version 15) loaded
Wed Dec 3 01:00:30 2025 kern.warn kernel: [ 26.462034] ath9k 0000:00:00.0: Direct firmware load for ath9k-eeprom-pci-0000:00:00.0.bin failed with error -2
Wed Dec 3 01:00:30 2025 kern.warn kernel: [ 26.472282] ath9k 0000:00:00.0: Falling back to sysfs fallback for: ath9k-eeprom-pci-0000:00:00.0.bin
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 26.993991] ath: phy0: Ignoring endianness difference in EEPROM magic bytes.
Wed Dec 3 01:00:30 2025 kern.debug kernel: [ 27.002691] ath: EEPROM regdomain: 0x0
Wed Dec 3 01:00:30 2025 kern.debug kernel: [ 27.002707] ath: EEPROM indicates default country code should be used
Wed Dec 3 01:00:30 2025 kern.debug kernel: [ 27.002718] ath: doing EEPROM country->regdmn map search
Wed Dec 3 01:00:30 2025 kern.debug kernel: [ 27.002742] ath: country maps to regdmn code: 0x3a
Wed Dec 3 01:00:30 2025 kern.debug kernel: [ 27.002756] ath: Country alpha2 being used: US
Wed Dec 3 01:00:30 2025 kern.debug kernel: [ 27.002769] ath: Regpair used: 0x3a
Wed Dec 3 01:00:30 2025 kern.debug kernel: [ 27.022290] ieee80211 phy0: Selected rate control algorithm ‚minstrel_ht‘
Wed Dec 3 01:00:30 2025 kern.info kernel: [ 27.024068] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0x6b16335b, irq=11
Wed Dec 3 01:00:30 2025 user.info kernel: [ 27.088305] kmodloader: done loading kernel modules from /etc/modules.d/*
Wed Dec 3 01:00:34 2025 kern.debug kernel: [ 56.512701] ath: EEPROM regdomain: 0x8114
Wed Dec 3 01:00:34 2025 kern.debug kernel: [ 56.512749] ath: EEPROM indicates we should expect a country code
Wed Dec 3 01:00:34 2025 kern.debug kernel: [ 56.512762] ath: doing EEPROM country->regdmn map search
Wed Dec 3 01:00:34 2025 kern.debug kernel: [ 56.512774] ath: country maps to regdmn code: 0x37
Wed Dec 3 01:00:34 2025 kern.debug kernel: [ 56.512789] ath: Country alpha2 being used: DE
Wed Dec 3 01:00:34 2025 kern.debug kernel: [ 56.512802] ath: Regpair used: 0x37
Wed Dec 3 01:00:34 2025 kern.debug kernel: [ 56.512814] ath: regdomain 0x8114 dynamically updated by user
Wed Dec 3 01:00:34 2025 user.notice : Added device handler type: vrf
Wed Dec 3 01:00:34 2025 user.notice : Added device handler type: bonding
Wed Dec 3 01:00:34 2025 user.notice : Added device handler type: 8021ad
Wed Dec 3 01:00:34 2025 user.notice : Added device handler type: 8021q
Wed Dec 3 01:00:34 2025 user.notice : Added device handler type: macvlan
Wed Dec 3 01:00:34 2025 user.notice : Added device handler type: veth
Wed Dec 3 01:00:34 2025 user.notice : Added device handler type: bridge
Wed Dec 3 01:00:34 2025 user.notice : Added device handler type: Network device
Wed Dec 3 01:00:34 2025 user.notice : Added device handler type: tunnel
Wed Dec 3 01:00:39 2025 user.info kernel: [ 61.599494] urngd: v1.0.2 started.
Wed Dec 3 01:00:54 2025 kern.info kernel: [ 77.237235] br-setup: port 1(eth0) entered blocking state
Wed Dec 3 01:00:54 2025 kern.info kernel: [ 77.242776] br-setup: port 1(eth0) entered disabled state
Wed Dec 3 01:00:54 2025 kern.info kernel: [ 77.248269] ag71xx-legacy 19000000.eth eth0: entered allmulticast mode
Wed Dec 3 01:00:54 2025 kern.info kernel: [ 77.255332] ag71xx-legacy 19000000.eth eth0: entered promiscuous mode
Wed Dec 3 01:00:54 2025 daemon.notice netifd: Interface ‚setup‘ is enabled
Wed Dec 3 01:00:54 2025 daemon.notice netifd: Interface ‚setup‘ is setting up now
Wed Dec 3 01:00:54 2025 daemon.notice netifd: Interface ‚setup‘ is now up
Wed Dec 3 01:00:54 2025 daemon.notice netifd: Interface ‚loopback‘ is enabled
Wed Dec 3 01:00:54 2025 daemon.notice netifd: Interface ‚loopback‘ is setting up now
Wed Dec 3 01:00:54 2025 daemon.notice netifd: Interface ‚loopback‘ is now up
Wed Dec 3 01:00:54 2025 daemon.notice netifd: Network device ‚lo‘ link is up
Wed Dec 3 01:00:54 2025 daemon.notice netifd: Interface ‚loopback‘ has link connectivity
:
ed Dec 3 01:00:56 2025 kern.info kernel: [ 79.300700] eth0: link up (100Mbps/Full duplex)
Wed Dec 3 01:00:56 2025 kern.info kernel: [ 79.305383] br-setup: port 1(eth0) entered blocking state
Wed Dec 3 01:00:56 2025 kern.info kernel: [ 79.310886] br-setup: port 1(eth0) entered forwarding state
Wed Dec 3 01:00:56 2025 daemon.notice netifd: Network device ‚eth0‘ link is up
Wed Dec 3 01:00:56 2025 daemon.notice netifd: bridge ‚br-setup‘ link is up
Wed Dec 3 01:00:56 2025 daemon.notice netifd: Interface ‚setup‘ has link connectivity
Wed Dec 3 01:01:29 2025 authpriv.info dropbear[1728]: Not backgrounding
Wed Dec 3 01:01:30 2025 daemon.err mount_root: failed - mount -t jffs2 /dev/mtdblock5 /rom/overlay: Not a tty
Wed Dec 3 01:01:30 2025 kern.err kernel: [ 113.416517] Too few erase blocks (3)
Wed Dec 3 01:01:32 2025 daemon.info dnsmasq[1785]: started, version 2.90 DNS disabled
Wed Dec 3 01:01:32 2025 daemon.info dnsmasq[1785]: compile time options: IPv6 GNU-getopt no-DBus UBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-nftset
no-auth cryptohash DNSSEC loop-detect inotify dumpfile
Wed Dec 3 01:01:32 2025 daemon.info dnsmasq-dhcp[1785]: DHCP, IP range 192.168.1.2 – 192.168.1.254, lease time 1h
Wed Dec 3 01:01:33 2025 user.notice led-trigger: LED trigger rssi is handled by /etc/init.d/rssileds
Wed Dec 3 01:01:33 2025 user.notice led-trigger: LED trigger rssi is handled by /etc/init.d/rssileds
Wed Dec 3 01:01:33 2025 user.notice led-trigger: LED trigger rssi is handled by /etc/init.d/rssileds
Wed Dec 3 01:01:33 2025 user.notice led-trigger: LED trigger rssi is handled by /etc/init.d/rssileds
Wed Dec 3 01:01:33 2025 daemon.info procd: - init complete -
Wed Dec 3 01:02:07 2025 kern.info kernel: [ 150.019105] eth0: link down
Wed Dec 3 01:02:07 2025 kern.info kernel: [ 150.022417] br-setup: port 1(eth0) entered disabled state
Wed Dec 3 01:02:07 2025 daemon.notice netifd: Network device ‚eth0‘ link is down
Wed Dec 3 01:02:08 2025 daemon.notice netifd: bridge ‚br-setup‘ link is down
Wed Dec 3 01:02:08 2025 daemon.notice netifd: Interface ‚setup‘ has link connectivity loss
Wed Dec 3 01:02:12 2025 kern.info kernel: [ 155.220573] eth0: link up (100Mbps/Full duplex)
Wed Dec 3 01:02:12 2025 kern.info kernel: [ 155.225239] br-setup: port 1(eth0) entered blocking state
Wed Dec 3 01:02:12 2025 kern.info kernel: [ 155.230728] br-setup: port 1(eth0) entered forwarding state
Wed Dec 3 01:02:12 2025 daemon.notice netifd: Network device ‚eth0‘ link is up
Wed Dec 3 01:02:12 2025 daemon.notice netifd: bridge ‚br-setup‘ link is up
Wed Dec 3 01:02:12 2025 daemon.notice netifd: Interface ‚setup‘ has link connectivity
Wed Dec 3 01:02:17 2025 daemon.info dnsmasq-dhcp[1785]: DHCPDISCOVER(br-setup) 192.168.1.134 f0:de:f1:24:f0:42
Wed Dec 3 01:02:17 2025 daemon.info dnsmasq-dhcp[1785]: DHCPOFFER(br-setup) 192.168.1.134 f0:de:f1:24:f0:42
Wed Dec 3 01:02:17 2025 daemon.info dnsmasq-dhcp[1785]: DHCPREQUEST(br-setup) 192.168.1.134 f0:de:f1:24:f0:42
Wed Dec 3 01:02:17 2025 daemon.info dnsmasq-dhcp[1785]: DHCPACK(br-setup) 192.168.1.134 f0:de:f1:24:f0:42 radioactive
Wed Dec 3 01:12:35 2025 kern.info kernel: [ 778.179108] eth0: link down
Wed Dec 3 01:12:35 2025 kern.info kernel: [ 778.182409] br-setup: port 1(eth0) entered disabled state
Wed Dec 3 01:12:35 2025 daemon.notice netifd: Network device ‚eth0‘ link is down
Wed Dec 3 01:12:36 2025 daemon.notice netifd: bridge ‚br-setup‘ link is down
Wed Dec 3 01:12:36 2025 daemon.notice netifd: Interface ‚setup‘ has link connectivity loss
Wed Dec 3 01:14:07 2025 kern.info kernel: [ 869.700602] eth0: link up (100Mbps/Full duplex)
Wed Dec 3 01:14:07 2025 kern.info kernel: [ 869.705272] br-setup: port 1(eth0) entered blocking state
Wed Dec 3 01:14:07 2025 kern.info kernel: [ 869.710759] br-setup: port 1(eth0) entered forwarding state
Wed Dec 3 01:14:07 2025 daemon.notice netifd: Network device ‚eth0‘ link is up
Wed Dec 3 01:14:07 2025 daemon.notice netifd: bridge ‚br-setup‘ link is up
Wed Dec 3 01:14:07 2025 daemon.notice netifd: Interface ‚setup‘ has link connectivity
Wed Dec 3 03:50:41 2025 kern.info kernel: [10264.019429] eth0: link down
Wed Dec 3 03:50:41 2025 kern.info kernel: [10264.022737] br-setup: port 1(eth0) entered disabled state
Wed Dec 3 03:50:41 2025 daemon.notice netifd: Network device ‚eth0‘ link is down
Wed Dec 3 03:50:42 2025 daemon.notice netifd: bridge ‚br-setup‘ link is down
Wed Dec 3 03:50:42 2025 daemon.notice netifd: Interface ‚setup‘ has link connectivity loss
Wed Dec 3 01:02:07 2025 kern.info kernel: [ 150.019105] eth0: link down
Wed Dec 3 01:02:07 2025 kern.info kernel: [ 150.022417] br-setup: port 1(eth0) entered disabled state
Wed Dec 3 01:02:07 2025 daemon.notice netifd: Network device ‚eth0‘ link is down
Wed Dec 3 01:02:08 2025 daemon.notice netifd: bridge ‚br-setup‘ link is down
Wed Dec 3 01:02:08 2025 daemon.notice netifd: Interface ‚setup‘ has link connectivity loss
Wed Dec 3 01:02:12 2025 kern.info kernel: [ 155.220573] eth0: link up (100Mbps/Full duplex)
Wed Dec 3 01:02:12 2025 kern.info kernel: [ 155.225239] br-setup: port 1(eth0) entered blocking state
Wed Dec 3 01:02:12 2025 kern.info kernel: [ 155.230728] br-setup: port 1(eth0) entered forwarding state
Wed Dec 3 01:02:12 2025 daemon.notice netifd: Network device ‚eth0‘ link is up
Wed Dec 3 01:02:12 2025 daemon.notice netifd: bridge ‚br-setup‘ link is up
Wed Dec 3 01:02:12 2025 daemon.notice netifd: Interface ‚setup‘ has link connectivity
Wed Dec 3 01:02:17 2025 daemon.info dnsmasq-dhcp[1785]: DHCPDISCOVER(br-setup) 192.168.1.134 f0:de:f1:24:f0:42
Wed Dec 3 01:02:17 2025 daemon.info dnsmasq-dhcp[1785]: DHCPOFFER(br-setup) 192.168.1.134 f0:de:f1:24:f0:42
Wed Dec 3 01:02:17 2025 daemon.info dnsmasq-dhcp[1785]: DHCPREQUEST(br-setup) 192.168.1.134 f0:de:f1:24:f0:42
Wed Dec 3 01:02:17 2025 daemon.info dnsmasq-dhcp[1785]: DHCPACK(br-setup) 192.168.1.134 f0:de:f1:24:f0:42 radioactive
Wed Dec 3 01:12:35 2025 kern.info kernel: [ 778.179108] eth0: link down
Wed Dec 3 01:12:35 2025 kern.info kernel: [ 778.182409] br-setup: port 1(eth0) entered disabled state
Wed Dec 3 01:12:35 2025 daemon.notice netifd: Network device ‚eth0‘ link is down
Wed Dec 3 01:12:36 2025 daemon.notice netifd: bridge ‚br-setup‘ link is down
Wed Dec 3 01:12:36 2025 daemon.notice netifd: Interface ‚setup‘ has link connectivity loss
Wed Dec 3 01:14:07 2025 kern.info kernel: [ 869.700602] eth0: link up (100Mbps/Full duplex)
Wed Dec 3 01:14:07 2025 kern.info kernel: [ 869.705272] br-setup: port 1(eth0) entered blocking state
Wed Dec 3 01:14:07 2025 kern.info kernel: [ 869.710759] br-setup: port 1(eth0) entered forwarding state
Wed Dec 3 01:14:07 2025 daemon.notice netifd: Network device ‚eth0‘ link is up
Wed Dec 3 01:14:07 2025 daemon.notice netifd: bridge ‚br-setup‘ link is up
Wed Dec 3 01:14:07 2025 daemon.notice netifd: Interface ‚setup‘ has link connectivity
Wed Dec 3 03:50:41 2025 kern.info kernel: [10264.019429] eth0: link down
Wed Dec 3 03:50:41 2025 kern.info kernel: [10264.022737] br-setup: port 1(eth0) entered disabled state
Wed Dec 3 03:50:41 2025 daemon.notice netifd: Network device ‚eth0‘ link is down
Wed Dec 3 03:50:42 2025 daemon.notice netifd: bridge ‚br-setup‘ link is down
Wed Dec 3 03:50:42 2025 daemon.notice netifd: Interface ‚setup‘ has link connectivity loss
Wed Dec 3 03:50:46 2025 kern.info kernel: [10269.220898] eth0: link up (100Mbps/Full duplex)
Wed Dec 3 03:50:46 2025 kern.info kernel: [10269.225572] br-setup: port 1(eth0) entered blocking state
Wed Dec 3 03:50:46 2025 kern.info kernel: [10269.231066] br-setup: port 1(eth0) entered forwarding state
Wed Dec 3 03:50:46 2025 daemon.notice netifd: Network device ‚eth0‘ link is up
Wed Dec 3 03:50:46 2025 daemon.notice netifd: bridge ‚br-setup‘ link is up
Wed Dec 3 03:50:46 2025 daemon.notice netifd: Interface ‚setup‘ has link connectivity
Wed Dec 3 03:50:50 2025 daemon.info dnsmasq-dhcp[1785]: DHCPDISCOVER(br-setup) 10.12.240.102 f0:de:f1:24:f0:42
Wed Dec 3 03:50:50 2025 daemon.info dnsmasq-dhcp[1785]: DHCPOFFER(br-setup) 192.168.1.134 f0:de:f1:24:f0:42
Wed Dec 3 03:50:50 2025 daemon.info dnsmasq-dhcp[1785]: DHCPDISCOVER(br-setup) 10.12.240.102 f0:de:f1:24:f0:42
Wed Dec 3 03:50:50 2025 daemon.info dnsmasq-dhcp[1785]: DHCPOFFER(br-setup) 192.168.1.134 f0:de:f1:24:f0:42
Wed Dec 3 03:50:50 2025 daemon.info dnsmasq-dhcp[1785]: DHCPREQUEST(br-setup) 192.168.1.134 f0:de:f1:24:f0:42
Wed Dec 3 03:50:50 2025 daemon.info dnsmasq-dhcp[1785]: DHCPACK(br-setup) 192.168.1.134 f0:de:f1:24:f0:42 radioactive
Wed Dec 3 03:50:51 2025 authpriv.info dropbear[1877]: Child connection from 192.168.1.134:50892
Wed Dec 3 03:50:52 2025 authpriv.info dropbear[1877]: Exit before auth from <192.168.1.134:50892>: Exited normally
Wed Dec 3 03:51:01 2025 authpriv.info dropbear[1878]: Child connection from 192.168.1.134:34170
Wed Dec 3 03:51:04 2025 authpriv.notice dropbear[1878]: Auth succeeded with blank password for ‚root‘ from 192.168.1.134:34170
Ich hoffe, das ist verwertbar.
Vielen Dank!
Das neue Image unter gleicher URL läuft offenbar, mal sehen, der Node sollte ja bald in der Knotenkarte auftauchen.
Vielen Dank, @fmaurer dann kann ich demnächst die Checkliste angehen.
Ist wohl ein typisches Problem, dass manche Geräte readonly booten, wenn die firmware zu groß ist.
Die nanostation hatte ich deshalb hier auch von einigen Paketen ausgeschlossen:
Das ist aber nur Community-Spezifisch.
Wenn die checkliste dann läuft wäre das schon cool
Da ich das Wochenende durch arbeite und noch einen Mesh-Partner bauen muss kann das etwas mehr Zeit brauchen…
Ich melde mich…
Alles super! Vielen Dank soweit und hat ja keine Eile!
Bis dann!
In anderen Communities würde das nicht funktionieren? Das geht nicht nach Gluon?
Ich bin ja eigentlich bei einer anderen Community …
›Neues Image unter alter URL‹?
Die image-customations.lua ist site-spezifisch, soweit ich das verstanden habe, müßte das Device in Gluon also mit class = 'tiny' hinzugefügt werden, damit das Image klein genug bleibt, daß noch die Konfiguration gespeichert wird — falls es denn daran lag.
- [X] Must be flashable from vendor firmware
- [X] Web interface
- [ ] TFTP
- [ ] Other: <specify>
- [X] Must support upgrade mechanism
- [ ] Must have working sysupgrade
- [ ] Must keep/forget configuration (`sysupgrade [-n]`, `firstboot`)
- [X] Gluon profile name matches autoupdater image name
(`lua -e 'print(require("platform_info").get_image_name())'`)
ubiquiti-rocket-m-xm
[X] Reset/WPS/... button must return device into config mode
- [X] Primary MAC address should match address on device label (or packaging)
(https://gluon.readthedocs.io/en/latest/dev/hardware.html#hardware-support-in-packages)
[?] When re-adding a device that was supported by an earlier version of Gluon, a
factory reset must be performed before checking the primary MAC address, as
the setting from the old version is not reset otherwise.
- Wired network
- [X] should support all network ports on the device
- [X] must have correct port assignment (WAN/LAN)
- if there are multiple ports but no WAN port:
- the PoE input should be WAN, all other ports LAN
- otherwise the first port should be declared as WAN, all other ports LAN
- Wireless network (if applicable)
- [X] Association with AP must be possible on all radios
- [X] Association with 802.11s mesh must work on all radios
- [X] AP+mesh mode must work in parallel on all radios
- LED mapping
- Power/system LED
- [X] Lit while the device is on
- [ ] Should display config mode blink sequence
(https://gluon.readthedocs.io/en/latest/features/configmode.html)
No. Last RSSI-LED has bink sequence
- Radio LEDs
- [X] Should map to their respective radio
- [X] Should show activity
- Switch port LEDs
- [X] Should map to their respective port (or switch, if only one led present)
- [X] Should show link state and activity
- Outdoor devices only:
- [?] Added board name to `is_outdoor_device` function in `package/gluon-core/luasrc/usr/lib/lua/gluon/platform.lua`
- Cellular devices only:
- [ ] Added board name to `is_cellular_device` function in `package/gluon-core/luasrc/usr/lib/lua/gluon/platform.lua`
- [ ] Added board name with modem setup function `setup_ncm_qmi` to `package/gluon-core/luasrc/lib/gluon/upgrade/250-cellular`
- Docs:
- [?] Added Device to `docs/user/supported_devices.rst`
Das erste Image, welches @fmaurer gebaut hat war zu gro0, das hat zu meinen anfänglichen Problemen geführt. Jetzt geht es ja.
Jetzt habe ich die Rocket gebrickt.
Was ich getan habe: bei der korrekt laufenden Software das alte “zu große” sysupgrade-Image ins Dateisystem geladen und mit sysupgrade instaliert,
Jetzt sieht das von den LEDs so aus, als würde die Rocket in den Config-Mode booten, ohne aber dass das LAN-Interface aktiv ist. Das ist Essig. Am Anfang des Boots ist das LAN Interface kurz aktiv (LED am Switch leuchtet kurz bis zum Laden von Gluon.
Der Versuch, einen Boot in den Config-Mode auszulösen scheitert (keine Reaktion), aber vermutlich bin ich in sowas wie dem Config-Modus nur ohne LAN.
Mist.
Hat jemand eine Idee für einen Debrick?
